How to clean a wireless keyboard?

by sogrow team

How to clean a wireless keyboard?

Overtime use, the keyboard gets dirty, even if you don't eat or smoke at your computer desk. Accumulated dust and dirt can adversely affect keyboard performance. In most cases, using compressed air and isopropyl alcohol to clean the keyboard is sufficient. It is more dangerous if liquid gets on the keyboard, in which case it should be dried immediately. Separate the keyboard and clean it properly to get rid of sticky buds. After that, it will look new.


Steps

Method 1: Remove the Trash

Turn off your computer and disconnect all cables. To protect your hardware from any damage, before cleaning your keyboard, turn off your computer. If you have a wired keyboard, unplug the cable that connects it to the computer. If you can't turn off the keyboard (for example, in a laptop), plug in the computer's power cable to reduce the risk of electric shock.

You can disconnect the USB wireless keyboard while the computer is running. However, if the keyboard is of a different type, such an attempt could harm the computer, so if you are not sure, it is best to turn off the computer first.

Remove batteries from the wireless keyboard, especially if you are going to clean the keys thoroughly.

Turn the keyboard upside down to move debris. Turn the keyboard over and shake it. Be careful when doing this. As a result, most of the tracks, debris, hair and other debris will fall off the keyboard. When you do this, tilt the keyboard at different angles and type at the bottom of the keyboard to remove as much debris as possible.

Hear the sound of debris rolling in the middle of the keyboard. Mechanical keyboards and other devices with raised keys can make this sound. In this case, consider disassembling and cleaning the keyboard.

If you are cleaning the laptop keyboard, open it and hold the monitor with one hand and the base with the other hand.

Blow away dust and debris from the keyboard with compressed air. Compressed air is the primary cleaning agent for cleaning keyboard surfaces. Take the can at a 45-degree angle and point it to the keys. Blow a jet of compressed air on the keyboard. At the same time, place the spray nozzle 1-2 cm from the keys.

Cans of compressed air can be purchased at electronics or office supply stores. It can also be ordered online.

Control different angles to clear the keyboard. Rotate the can in different directions.

If you are cleaning a laptop keyboard or membrane keyboard, try to stop it by blowing compressed air. Hold the keyboard straight at an angle of about 75 degrees in the airflow.

Remove trapped debris with a vacuum cleaner. The vacuum cleaner will help remove most of the particles trapped between the keys. If you do not have a vacuum cleaner with a hose, try using a regular vacuum cleaner with a brush attached. Look at the whole keyboard and pay special attention to the difference between the keys. Most of the trash is hidden here.

Make sure all keys are kept securely in place, especially if you are working with a laptop. If a key is sucked into a vacuum cleaner, remove it from the dustbin, wash it and put it back. Clip the key to the pin or clip to reconnect to the keyboard.

Wipe the space between the keys with cotton wool dipped in isopropyl alcohol. Moisten a cotton swab slightly so that a large amount of moisture does not get under the keys. Run a cotton swab around each key to remove dust, grease, and other dirt. Repeat as many times as necessary and clean the sides of each key thoroughly. When the cotton bush gets dirty, replace it with a clean one.

Spill alcohol dries very quickly, so it is better to clean the keyboard than plain water. It can be bought at a pharmacy or supermarket.

Instead of a cotton swab, you can use a microfiber wrapped around the tip of a knife. Moisten it with alcohol and erase the space between the keys. This method is best for clearing the mechanical keyboard with the raised keys.

Be careful with your laptop. Isopropyl wines are also good for this, but other components under the laptop keyboard can be easily damaged. Be careful not to get moisture under the keys.

Wipe the keyboard with a cloth soaked in alcohol. Use a lint-free cloth or paper towel to avoid adding new debris. Alcohol should not drip from the cloth after wetting. Remove dust and other debris from the surface of each key.

Take a closer look at commonly used keys (for example, the space bar and interlock). They usually have more dirt on them. Completely remove these buds. You may need to wipe several times to wipe.

Remove dirt from heavy dirt areas with a toothpick. Show the toothpick parallel to the key and wipe off the dirt. After that, wipe the key with alcohol.


Polish the keyboard with an indication-free cloth. Wipe the keyboard one last time to remove any dust and moisture. Review the keyboard: If there is any dirt in it, consider cleaning it more thoroughly. After clearing the keyboard, connect it to your computer and see how it works.

Let the remaining alcohol on the keys dry in a few minutes. The water dries out for a long time. If you have used water to clean your keyboard or suspect it is damp, wait 24 hours for it to dry completely before connecting it to your computer.


Method 2: Clear the liquid from the keyboard

Turn off the computer and disconnect the keyboard from the computer. If you spill liquid on the keyboard, turn off the computer immediately. Liquid can peek into the keyboard and damage the keyboard and other components using a laptop. For a wired keyboard, disconnect this cable from the computer. Turn off the power before liquid spilt on the laptop keyboard.

Take immediate action to avoid damaging your keyboard and computer. Liquids have a bad effect on electrical components. Do not turn on the computer until the keyboard is dry.

Before disconnecting the wired keyboard, please turn it off to avoid damaging the computer.

Turn the keyboard upside down and try to move the liquid. Turn the keyboard upside down on a sink, trash can, or towel to get the liquid out instead of sinking it upside down. Shake the keyboard to move a drip between the keys. Keep shaking the keyboard until the liquid shakes.

Tilt the keyboard to drain the liquid. If you have a laptop, direct the liquid to the keyboard so that the monitor and other key components are not damaged. Turn the laptop open again so that the liquid flows towards the keyboard and spreads out.

Dry the keyboard with a microfiber cloth. Keep the keyboard upside down while doing this. Try to remove as much liquid as possible with rags. Do not turn the keyboard until you have cleared everything.

Paper towels and regular textiles leave traces behind, so try using microfiber. If you desperately need to erase your keyboard and don't have the right cloth on hand, use one that has fewer hints. Paper towels, tea towels, or even an old T-shirt will work.

Wait at least 24 hours for the keyboard to dry. Turn the keyboard upside down to remove any remaining liquid. Place a piece of the cloth-like towel under the keyboard to absorb the liquid. When the keyboard is dry, you can replace it.

In most cases, 24 hours is enough to dry all the spilled liquid. If you have time, keep dry the keyboard for 2-3 days.

Connect a wired keyboard to your computer or turn on your laptop. Try printing something. Check each key. You may need to remove the individual keys and clear them.

If you don't spill water but something else, some keys may remain. In that case, you will need to disassemble the keyboard and clean it from the inside.

If you draw liquid on an expensive laptop, consider contacting a professional. Laptops are much more delicate and difficult to clean than regular keyboards. The technician will be able to check if the internal components of the laptop have been damaged.


Method 3: Cleaning the inside of the keyboard

Shut down the computer and unplug the keyboard. This is important for your computer and its security. Turn off the computer first, and then disconnect the keyboard from the computer. If you have a wireless keyboard, remove the battery from the keyboard.

Unplug the power cord if you are using a laptop. Press any key to make sure the laptop is completely off.

If you are using a wired keyboard, turn it off before disconnecting your computer.

If the keys come in, pull them out with a screwdriver. On most modern keyboards, the keys are attached to small clips and can be easily removed. Use a flat screwdriver or butter knife to press the corner of the key, hold it slightly up and try to pull it with your fingers. To remove it from the slot, you have to insert a key or PC from the opponent.

Before taking out the keys, take a picture of the keyboard from your mobile phone. This will help you enter the keys in the correct order.

If you have trouble extracting the keys, check the manual that came with the keyboard or consult a professional on how to disassemble and clean the keyboard.

If possible, open the keyboard and open it. Flip the keyboard and find the patch. Some keyboards have two panels curved together. If there is a patch on the keyboard

So, open them, remove the debris below and clean it separately. Check the screw under the label on the keyboard.

If the keys do not move, then the bezel can usually be removed. Then, if possible, remove the keys to clean the bezel better.

Place the keys in a colander and rinse with warm water. Place a towel near the sink. Run hot water from the tap and put the keys in a colander. Place a colander under running hot water and shake the keys with your hand to rinse them thoroughly. This water will wash away any debris and spill into the holes in the bottom of the colander. After that, dry the keys on the towel. Sprinkle

If water doesn't wash away all the dirt, try using liquid dish soap. Fill a bowl with warm water and add a tablespoon (15 ml) of liquid soap to the foam solution. Toothpaste can be used instead of liquid soap.

Clean the empty bezel with warm water and soap. Place the panel in a colander or bowl and rinse with warm water. To remove stubborn dirt, clean the dirt with a microfiber cloth and soap and water. Then set the panel aside and wait for it to dry.

If the keyboard is very dirty, soak the apples and keys in soap and water for 6 hours. After that, rub the panel and keys and rinse off the rest of the dirt.

Wipe the other half of the keyboard with a cloth soaked in alcohol. Take a clean, shin-free cloth and moisten it with isopropyl alcohol. Try clearing any debris from the bottom panel. Run rags on the clips holding the keys.

Make sure no alcohol seeps into the fabric. Otherwise, moisture will not reach the electronic components. Remove stubborn dirt with electronics cleaning from electronics stores.

Clean the key slot with a cotton swab filled with alcohol. Remove any dirt and debris from the keyboard. Key slots are small tabs or clips. Wipe the sides of each clip to remove any dirt from it. Next, lightly moisten a cotton swab with a clean cloth and wipe the top of each clip.

When the cotton bush gets dirty, replace it with a clean one to avoid leaving debris when wiping.

Isopropyl alcohol dries quickly, so it is better to clean the keyboard than water. However, please don't use too much rubbing alcohol and lighten a cotton swab with it.

Let the keyboard dry for 2-3 days. Choose a suitable place on the table. Cover it with a towel and spread the details on it. Wait for them to dry.

Keep the parts in a safe place to avoid falling or getting lost on the floor. Dry them out of reach of children and pets.

Assemble the keyboard and test how it works. Reverse the steps you took when disassembling the keyboard. For most keyboards, the panels must be connected first. Twist the panels together, then insert the keys into their respective clips or slots. This is usually enough to press the key to fit into the socket lightly.

If the keyboard does not work, check that you have assembled it correctly and that all the wires are connected to it.

If you need to clean your laptop, consider seeking professional help. A professional will be able to disassemble a laptop, locate damaged parts, and safely clean electronic components.